Stade Mirror

Working with natural materials means that color tones and grain markings will differ from sample to sample and from one finished piece to the next. Every item is uniquely its own—one of the qualities we love most. Over time, aging and exposure to light may subtly shift the appearance of your furniture.

24"W x 36"H x 1 5/8"D

All mirrors employ a french cleat hanging system, with the mirror cleat pre-attached to the back of the frame and the wall cleat included in the packaging. The most secure way of mounting the wall cleat is with cabinet screws (included) drilled into wooden wall studs. When no studs are present, a variety of methods and hardware are available for mounting to drywall, plaster, masonry, etc., but are not included. For this reason, and if no studs are present, it is recommended that the mirror be hung by a professional handyman, carpenter, or contractor. Incorrect hanging of mirror frames may result in personal injury, and/or cause damage to the mirror or surrounding fixtures. 

If mounting is not conducted by a professional, consult a local hardware or home improvement store, being sure to purchase the correct hanger for the type of wall and weight of the mirror. When you’re ready to hang the mirror ensure access to the following tools:

• Masking tape
• Level
• Pencil
• Drill
• Non-stud wall hangers (not included)
• #8 x 2” cabinet screws (included, for use when mounting to wall studs ONLY)

1. Place a piece of masking tape on the wall at the approximate desired height of the mirror frame’s top edge, about center of the mirror’s width.
2. Writing on the masking tape, mark the desired top edge height, about center of the mirror’s width.
3. With the mirror frame lying on a flat surface, mirror-side down, hold the wall cleat against the mirror cleat. Ensure each cleat’s angled protrusion fits tightly against that of the opposite cleat.
4. Holding the connected cleats steady, measure the distance from the top of the mirror frame to the center of the holes on the wall cleat. Record this distance.
5. Using the distance found in Step 4, measure down from the mark made in Step 2. Mark this new height on the wall. Double check the distance between the two marks equals that found in Step 4.
6. Using a level, draw a line at the height found in step 5, extending about an inch past the full width of the cleat and centered on the desired left-to-right placement of the mirror.
7. Vertically center the wall cleat’s screw holes along the line, while ensuring the cleat is centered left-to-right on the frame’s final placement. 
8. With the wall cleat centered, mark three of the screw holes on the wall, with one at either end and one about center. Set the wall cleat aside. *Extra screw holes in the cleat are for alignment to wall studs, if any are present. It is not necessary to use more than three screws for mounting the wall cleat as long as they are spaced somewhat evenly between left, right, and center.
9. If drilling into a wall stud, pre-drill through the marked cleat holes where studs are present.
10. When no stud is present, follow manufacturer’s instructions for inserting hangers, ensuring they are placed at the marked screw holes.
11. Mount the wall cleat. If using drywall or plaster hangers, it is recommended to use a screw driver while tightening the hangers in order to better feel when they are snug and avoid over-tightening.
12. Re-check the cleat is level and centered left-to-right. If not, loosen screws and shift the cleat’s ends up or down as needed until level is achieved. Re-tighten screws. 
13. Using fingertips, offer moderate downward and side-to-side pressure to the wall cleat, ensuring it is tight to the wall and doesn’t move when put under weight. 
14. Gently lift the mirror over the wall cleat, then slowly bring it downward, ensuring the angled protrusion of the mirror cleat is sitting in the matched protrusion of the wall cleat. It is helpful to have a second person looking behind the mirror for alignment and to make sure the cleats catch each other.
15. Slide the mirror left or right as needed. There is no vertical adjustment.
16. A properly installed mirror frame will sit about ⅛” off the wall, with the bumpers in the lower corners resting against the wall.

All mirrors are final sale and not eligible for return. If your order arrives damaged or defected, please reach out to hello@shopbrunel.com within 48 hours of delivery for assistance. 

Shipping fees are not included in the price of your product. Brunel ships to the continental US and is unable to ship to PO Boxes. Rates will be calculated at checkout based on the item details, destination, and mode of shipping. Local delivery and pick-up options are available upon request. If you have questions about shipping please reach out to hello@shopbrunel.com

Shipping rates displayed at checkout are calculated to the best of our ability based on current carrier rates and destination information. However, due to fluctuations in shipping costs, package dimensions, or delivery locations, actual shipping charges may vary.

We reserve the right to adjust shipping fees if the calculated rate at checkout is found to be inaccurate. In the event of a rate adjustment, customers will be notified prior to shipment and given the opportunity to approve the updated shipping cost or cancel the order for a full refund.

Wood finishes: Because solid wood is an active, natural material, it reacts to its surroundings—particularly shifts in temperature and humidity. Minor surface checks can occur and are considered normal. Keeping your space at a steady humidity level helps minimize movement or warping. For everyday upkeep, dust regularly and wipe with a lightly dampened microfiber cloth.